STS-335 STS-135 ATLANTIS ENGINE #1 INSTALLATION

STS-335 STS-135 ATLANTIS ENGINE #1 INSTALLATION
SuperStock offers millions of photos, videos, and stock assets to creatives around the world. This image of STS-335 STS-135 ATLANTIS ENGINE #1 INSTALLATION by Piemags/PL Photography Limited is available for licensing today.

Visually Similar More from Space Shuttle Preparation story

RM
6145-44893309
CAPE CANAVERAL, Fla. - Inside Orbiter Processing Facility-1 at NASAs Kennedy Space Center in Florida, United Space Alliance technicians monitor the progress as a large crane lifts the right orbital maneuvering system, or OMS, pod for installation on space shuttle Atlantis. It is the last time an OMS pod will be installed on Atlantis. The OMS provided the shuttle with thrust for orbit insertion, rendezvous and deorbit, and could provide up to 1,000 pounds of propellant to the aft reaction control system.The OMS is housed in two independent pods located on each side of the shuttles aft fuselage. Each pod contains one OMS engine and the hardware needed to pressurize, store and distribute the propellants to perform the velocity maneuvers. Atlantis OMS pods were removed and sent to the test facility at White Sands Space Harbor in New Mexico to be cleaned of residual toxic propellant. The work is part of the Space Shuttle Programs transition and retirement processing of the space shut
RM
6145-44881039
T&R Endeavour, LH Oms Pod Lift and Move for Installation
RM
6145-44881793
CAPE CANAVERAL, Fla. - In Orbiter Processing Facility-2 at NASAs Kennedy Space Center in Florida, United Space Alliance technicians monitor the progress as a large crane is lowered toward the right orbital maneuvering system OMS pod that will be installed on space shuttle Endeavour. The OMS pod underwent complete deservicing and cleaning at White Sands Space Harbor in New Mexico, part of the transition and retirement processing of each shuttle. Endeavour is being prepared for public display at the California Science Center in Los Angeles. Over the course of its 19-year career, Endeavour spent 299 days in space during 25 missions.
RM
6145-44791648
CAPE CANAVERAL, Fla. - Pratt & Whitney Rocketdyne technicians align a space shuttle main engine for installation on space shuttle Endeavour in Orbiter Processing Facility Bay 2 at NASA's Kennedy Space Center in Florida. The engine will fly on the shuttle's STS-130 mission to the International Space Station. Even though this engine weighs one-seventh as much as a locomotive engine, its high-pressure fuel pump alone delivers as much horsepower as 28 locomotives, while its high-pressure oxidizer pump delivers the equivalent horsepower of an additional 11 locomotives. The maximum equivalent horsepower developed by the shuttle's three main engines is more than 37 million horsepower. Endeavour is targeted to launch Feb. 4, 2010.
RM
6145-45062020
VANDENBERG AIR FORCE BASE, Calif. - The canister containing the interstage adapter, or ISA, for NASA's Soil Moisture Active Passive mission, or SMAP, is lifted out of its transportation trailer in the high bay of the Building 836 hangar on south Vandenberg Air Force Base in California.A United Launch Alliance Delta II rocket will loft SMAP into orbit from Vandenberg's Space Launch Complex 2. The ISA connects the Delta II first and second stages and encloses the second stage engine and thrust section. The spacecraft will provide global measurements of soil moisture and its freeze/thaw state. These measurements will be used to enhance understanding of processes that link the water, energy and carbon cycles, and to extend the capabilities of weather and climate prediction models. The data returned also will be used to quantify net carbon flux in boreal landscapes and to develop improved flood prediction and drought monitoring capabilities. Launch is scheduled for November 2014.
RM
6145-44894675
CAPE CANAVERAL, Fla. - In Orbiter Processing Facility-1 at NASAs Kennedy Space Center in Florida, a technician moves the Hyster forklift carrying replica shuttle main engine RSME number 1 toward space shuttle Atlantis. Three RSMEs will be installed on Atlantis.The work is part of the Space Shuttle Programs transition and retirement processing of the space shuttle fleet. A groundbreaking was held Jan. 18 for Atlantis future home, a 65,000-square-foot exhibit hall in Shuttle Plaza at the Kennedy Space Center Visitor Complex. Atlantis is scheduled to roll over to the visitor complex in November in preparation for the exhibits grand opening in July 2013.
RM
6145-44896316
CAPE CANAVERAL, Fla. - In Orbiter Processing Facility Bay 1 at NASAs Kennedy Space Center in Florida, technicians work with the Hyster forklift as replica shuttle main engine RSME number 3 is installed on the space shuttle Endeavour.The work is part of Transition and Retirement of the remaining space shuttles, Endeavour and Atlantis. Endeavour is being prepared for public display at the California Science Center in Los Angeles. Its ferry flight to California is targeted for mid-September. Endeavour was the last space shuttle added to NASAs orbiter fleet. Over the course of its 19-year career, Endeavour spent 299 days in space during 25 missions.
RM
7137-70494533
Assembly work at the Beechcraft factory in Wichita, Kansas.
RM
6145-44791650
CAPE CANAVERAL, Fla. - A Pratt & Whitney Rocketdyne technician carefully maneuvers a space shuttle main engine into position on space shuttle Endeavour in Orbiter Processing Facility Bay 2 at NASA's Kennedy Space Center in Florida. The engine will fly on the shuttle's STS-130 mission to the International Space Station.Even though this engine weighs one-seventh as much as a locomotive engine, its high-pressure fuel pump alone delivers as much horsepower as 28 locomotives, while its high-pressure oxidizer pump delivers the equivalent horsepower of an additional 11 locomotives. The maximum equivalent horsepower developed by the shuttle's three main engines is more than 37 million horsepower. Endeavour is targeted to launch Feb. 4, 2010.
RM
6145-44585774
KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, an orbiter main engine is lifted by a new engine hyster, built by Rocketdyne, that is used to remove it from the orbiter. .
RM
6145-44881790
CAPE CANAVERAL, Fla. - In Orbiter Processing Facility-2 at NASAs Kennedy Space Center in Florida, United Space Alliance technicians prepare a large crane that will lift the right orbital maneuvering system OMS pod for installation on space shuttle Endeavour. The OMS pod underwent complete deservicing and cleaning at White Sands Space Harbor in New Mexico, part of the transition and retirement processing of each shuttle. Endeavour is being prepared for public display at the California Science Center in Los Angeles. Over the course of its 19-year career, Endeavour spent 299 days in space during 25 missions.
RM
6145-45120991
In the Integration Facility at the Baikonur Cosmodrome in Kazakhstan, technicians complete work on the Soyuz MS-03 spacecraft for its encapsulation into the upper stage of its Soyuz booster Nov. 9. Expedition 50-51 crewmembers Peggy Whitson of NASA, Oleg Novitskiy of the Russian Federal Space Agency (Roscosmos) and Thomas Pesquet of the European Space Agency will launch on the Soyuz Nov. 18, Baikonur time, for a six-month mission on the International Space Station.NASA/Alexander Vysotsky
RM
6145-58972131
VANDENBERG AIR FORCE BASE, Calif. - The second stage for NASA's Orbiting Carbon Observatory-2 mission, or OCO-2, is suspended from the ceiling of the high bay of the Building 836 hangar on Vandenberg Air Force Base in California following its removal from the transportation trailer in which it arrived. OCO-2 is scheduled to launch aboard a United Launch Alliance Delta II rocket from Space Launch Complex 2 in July. The rocket's second stage will insert OCO-2 into a polar Earth orbit. OCO-2 will collect precise global measurements of carbon dioxide in the Earth's atmosphere and provide scientists with a better idea of the chemical compound's impacts on climate change. Scientists will analyze this data to improve our understanding of the natural processes and human activities that regulate the abundance and distribution of this important atmospheric gas.
RM
6145-44578863
KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, Columbia's engine no. 2 is about to be removed. After small cracks were discovered on the LH2 Main Propulsion System (MPS) flow liners in two other orbiters, program managers decided to move forward with inspections on Columbia before clearing it for flight on STS-107. The heat shields were removed, and after removing the three main engines, inspections of the flow liners will follow. The July 19 launch of Columbia on STS-107 has been delayed a few weeks
RM
6145-44708194
CAPE CANAVERAL, Fla. - In Orbiter Processing Facility bay No. 1, one of the three main engines for space shuttle Atlantis is positioned near the aft for installation. Main engine No. 1 has already been installed. Atlantis is the designated vehicle for the STS-125 mission to service the Hubble Space Telescope. Launch is targeted for Oct. 8.
RM
6145-45012627
T&R Endeavour, Alta Pod Installation/Demo, Enterprise/Smithsonia, Day 2
RM
1840-13175
two mechanics working on a thrust reverser for a regional commercial jet
RM
6145-44881021
CAPE CANAVERAL, Fla. -- In Orbiter Processing Facility-2 at NASA's Kennedy Space Center in Florida, operations to lift the left orbital maneuvering system OMS pod of space shuttle Endeavour are under way. The OMS pod is being reinstalled on Endeavour following a complete deservicing and cleaning at White Sands Space Harbor in New Mexico, part of the shuttles transition and retirement processing.Endeavour is being prepared for public display at the California Science Center in Los Angeles. Over the course of its 19-year career, Endeavour spent 299 days in space during 25 missions.
RM
6145-44854961
Discovery/T&R FRCS Removal & Lift to Transporter
RM
6145-44896081
CAPE CANAVERAL, Fla. - In Orbiter Processing Facility Bay 2 at NASAs Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour.The work is part of Transition and Retirement of the remaining space shuttles, Endeavour and Atlantis. Endeavour is being prepared for public display at the California Science Center in Los Angeles. Its ferry flight to California is targeted for mid-September. Endeavour was the last space shuttle added to NASAs orbiter fleet. Over the course of its 19-year career, Endeavour spent 299 days in space during 25 missions.
RM
6145-44602728
In the Orbiter Processing Facility, Tim Chastain (left) and John Peterson (right), with United Space Alliance, prepare to remove the body flap actuator from the orbiter Endeavour. The work is part of return to flight activities on the orbiter fleet.
Royalty Free License
Royalty-Free Standard Commercial licenses are granted for worldwide, non-exclusive and perpetual use, unless specifically noted otherwise. All Royalty-Free transactions are final. The Royalty-Free Standard Commercial license has no limitations and covers up to 15 users.
  • $50.00 Low500 X 500
  • $150.00 Med750 X 750
  • $250.00 High2100 X 2100
  • $350.00 Super High7000 X 7000
$1,225.00
RF High / Super Res 5 Pack
Save $525.00
$245.00
per download
Order a Framed Print
Looking for a license?
Click here, and we'll help you find it! Questions? Just ask!
DETAILS
Image Number: 6145-44840778Royalty FreeCredit Line:Piemags/PL Photography Limited/SuperStockCollection:PL Photography LimitedStory:Space Shuttle PreparationContributor:PiemagsModel Release:NoProperty Release:NoResolution:3000×1996